Fundamental Plumber Guide for Bathtub Installation
Visit My WebsiteThey are making a few great pointers about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround overall in this article directly below.
Mounting a tub isn't specifically rocket science, however it does need solid plumbing, woodworking, and in some cases, tiling abilities. Replacing an old tub with a brand-new one is likewise a moderately difficult job. If the old bathtub is conveniently easily accessible, the project can relocate immediately; if you have to open up a wall to remove the old bathtub and also position the brand-new bathtub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to leave the old tub and also embeded in the brand-new one. See to it you have actually certified on your own for the task as well as are comfortable trying it. Rather than employing a professional to take over a halfway-completed project, it is far better to think about employing one prior to you begin. Chances are you may require a specialist plumber to make tube connections.
This post will certainly aid you install a brand-new bathtub in your shower room if you have actually already gotten a brand-new bathtub and do not need to alter the setup of your previous water supply pipelines.
Your tools and also material checklist must consist of the following:
Planning for the Setup
First of all, the sustaining structure supplied with the bath should be fitted (if needed) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is essential to make certain that if the tap comes with a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets device to avoid stress on the bath tub.
Fit the adaptable tap connectors to the bottom of both faucets using 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you make use of all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must now be ready to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water. After doing so, activate the taps to drain pipes any type of water staying in the system. The procedure of eliminating the existing taps can be rather problematic because of the limited accessibility that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a cloth ready for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have actually been removed, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Prior to carrying on to fit the new faucets, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Tub
Using the two wood boards under its feet, place the bath tub in the called for placement. The wood boards are practical in equally spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto 4 tiny factors.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by checking the level and also readjusting the feet on the bath tub until the spirit level reviews degree.
To install taps, fit all-time low of the furthest versatile tap adapter to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
Turn on the supply of water and also inspect all joints as well as new pipework for leakages and tighten them if required. Load the bathtub and also examine the overflow outlet and also the regular outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the producer's instruction manual. Tiling as well as sealing around the bathtub needs to wait up until the tub has been used at the very least when as this will settle it right into its last placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the connector fits on the plastic tail of the faucet and the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the mounting opening in the bath/basin making certain that the washing machines remain in area between the tap as well as the sink. Safeguard the tap in position with the producer given backnut. Once the tap is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical faucet connectors. The previous type should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to split an inflexible seal, triggering the water to pass through the wall surface between the bath as well as the tiling, leading to complications with moisture and feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your components and fittings. They are offered in tubes as well as cartridges, and are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in usage. The sealant can break relatively very early if you do not take into consideration this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently offered on the market. It is a good idea to fit the tiles using waterproof or waterproof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm very focused on A Step-by-Step Guide to Installing a Bathtub and I really hope you enjoyed our entry. Sharing is nice. Helping others is fun. I praise you for your time. Visit us again soon.
Schedule And Pricing